AT-50....From Holland

People from all over the world can present your mopeds here, or you can ask whatever you want to know about mopeds.
Odgovori
Uporabniški avatar
TomosHolland
kriva felna
Prispevkov: 56
Pridružen: Če Mar 10, 2011 9:42 pm

Re: AT-50....From Holland

Odgovor Napisal/-a TomosHolland »

alright i got it running (a bit)

i tried jet 96 with choke (!!!) and it ran like crazy, really fast

only the piston is all worn and ugly so i am going to replace that first,

Sound : http://www.youtube.com/watch?v=bTR6FB1WjK4
Uporabniški avatar
TomosHolland
kriva felna
Prispevkov: 56
Pridružen: Če Mar 10, 2011 9:42 pm

Re: AT-50....From Holland

Odgovor Napisal/-a TomosHolland »

alright, i need your help

i need to set the ignition, but i am not 100% percent sure how, do you guys have a tutorial for me? (preferreably with pictures)
Uporabniški avatar
TomosHolland
kriva felna
Prispevkov: 56
Pridružen: Če Mar 10, 2011 9:42 pm

Re: AT-50....From Holland

Odgovor Napisal/-a TomosHolland »

anyone?

and how far must the contactpoints open ? .30mm?
Uporabniški avatar
maxbond1995
glava cilindra
Prispevkov: 568
Pridružen: Sr Jul 07, 2010 3:05 pm
Kraj: Šempeter pri Gorici

Re: AT-50....From Holland

Odgovor Napisal/-a maxbond1995 »

The point of pre-ignition is that the fuel has enough time for burn completely.
For setting pre-ignition you unscrew spark plug, put a caliper into the valve and measure the higher position of the piston. You must rotate flywheel by hand counterclockwise.
Now, you set the caliper 0.8mm lower than the highest position of the piston (example: if you measured 30mm, you set the new distance to 30,8mm). Now you turn the flywheel again. At the point when piston hits the caliper, you draw two dots on the same line, one on the rotor, one on the case of the engine. So, when this to dots meet, at that time contacts should start to open. You can configurate this by revolving a stator behind the rotor.
To test when the contacts begin to open it's most useful to use multimeter (ohmmeter), or you can just turn the flywheel to open the contacts, place between them a thin sheet of paper, turn the flywheel backward and pull the paper at the same time you turn the flywheel.
I hope you understood most of the thing, sorry for unperfect english :) .
Lp, Maks
Uporabniški avatar
maxbond1995
glava cilindra
Prispevkov: 568
Pridružen: Sr Jul 07, 2010 3:05 pm
Kraj: Šempeter pri Gorici

Re: AT-50....From Holland

Odgovor Napisal/-a maxbond1995 »

You can help with this: http://www.scribd.com/doc/29821910/Puch ... ice-Manual
It's the same thing, only thing you must pay attention to is in what direction in the arrow on the flywheel turned to!
And i forgot to think about this- are you using electronic ignition without contacts or the ordinary one?
Lp, Maks
Uporabniški avatar
TomosHolland
kriva felna
Prispevkov: 56
Pridružen: Če Mar 10, 2011 9:42 pm

Re: AT-50....From Holland

Odgovor Napisal/-a TomosHolland »

hmm its still complicated,

and which sprocket ratio do you guys recommend me with bt?
i want to keep as much acceleration but no over-revs , in Holland i can only get front-sprocket 12


and for rear-sprocket i use Rieju rear-sprocket (6 holes, this one : http://www.speed-parts.nl/tandwielen/ac ... rieju.html )

do they fit?

so i need to know which rear-sprocket i need ; so 12/??
Uporabniški avatar
aljo69
el presidente
Prispevkov: 6818
Pridružen: Po Avg 10, 2009 1:53 pm
Kraj: Celje

Re: AT-50....From Holland

Odgovor Napisal/-a aljo69 »

TomosHolland napisal/-a:hmm its still complicated,

and which sprocket ratio do you guys recommend me with bt?
i want to keep as much acceleration but no over-revs , in Holland i can only get front-sprocket 12


and for rear-sprocket i use Rieju rear-sprocket (6 holes, this one : http://www.speed-parts.nl/tandwielen/ac ... rieju.html )

do they fit?

so i need to know which rear-sprocket i need ; so 12/??
you need the smallest one ... like 32 or something
Uporabniški avatar
TomosHolland
kriva felna
Prispevkov: 56
Pridružen: Če Mar 10, 2011 9:42 pm

Re: AT-50....From Holland

Odgovor Napisal/-a TomosHolland »

aljo69 napisal/-a:
TomosHolland napisal/-a:hmm its still complicated,

and which sprocket ratio do you guys recommend me with bt?
i want to keep as much acceleration but no over-revs , in Holland i can only get front-sprocket 12


and for rear-sprocket i use Rieju rear-sprocket (6 holes, this one : http://www.speed-parts.nl/tandwielen/ac ... rieju.html )

do they fit?

so i need to know which rear-sprocket i need ; so 12/??
you need the smallest one ... like 32 or something
smallest is 36 this one
10007.jpg
10007.jpg (6.22 KiB) Pogledano 6831 krat
so 12/36 ratio will work good?
Uporabniški avatar
aljo69
el presidente
Prispevkov: 6818
Pridružen: Po Avg 10, 2009 1:53 pm
Kraj: Celje

Re: AT-50....From Holland

Odgovor Napisal/-a aljo69 »

TomosHolland napisal/-a:
aljo69 napisal/-a:
TomosHolland napisal/-a:hmm its still complicated,

and which sprocket ratio do you guys recommend me with bt?
i want to keep as much acceleration but no over-revs , in Holland i can only get front-sprocket 12


and for rear-sprocket i use Rieju rear-sprocket (6 holes, this one : http://www.speed-parts.nl/tandwielen/ac ... rieju.html )

do they fit?

so i need to know which rear-sprocket i need ; so 12/??
you need the smallest one ... like 32 or something
smallest is 36 this one

Slika

so 12/36 ratio will work good?
does it fit ?
Uporabniški avatar
TomosHolland
kriva felna
Prispevkov: 56
Pridružen: Če Mar 10, 2011 9:42 pm

Re: AT-50....From Holland

Odgovor Napisal/-a TomosHolland »

aljo69 napisal/-a:


does it fit ?
i hope so, it looks like the AT50 one, but here in holland you can only get at/atx/ntx/bt rear-sprocket with 46 or 47 teeth,

so i have to buy one from other motorcycle
Odgovori