Stran 3 od 8
Re: Im form the Netherlands and this are my mopeds
Objavljeno: Sr Jan 05, 2011 8:42 pm
Napisal/-a aljo69
uporabnik007 napisal/-a:2pac napisal/-a:i know thats the problem
i have a ctx engine with a 50cc cilinder
becouse in the right side i have circle in my carter
and the normal ntx did have a squere
you cant have ctx engine with 50cc cilinder.
word ! as far as i know ntx have stock atx engine
Re: Im form the Netherlands and this are my mopeds
Objavljeno: Sr Jan 05, 2011 8:45 pm
Napisal/-a 2pac
and here everybody drives a standard a3
because the most a3 drive 25 and than you dont have to wear a helmet
Most sellings in the netherlands a year
-standard a3 25km 40000 sells a year
-standard a3 45km 4000
-streetmate 21
-revival 200
--youngster 400
-funtastic 700
-sporter 15
yes realy i can make pictures
Re: Im form the Netherlands and this are my mopeds
Objavljeno: Sr Jan 05, 2011 8:48 pm
Napisal/-a automatic_7
the same is here in SLO
if your moped go 25km/h
you dont need nothing (only old 12 years)
Re: Im form the Netherlands and this are my mopeds
Objavljeno: Sr Jan 05, 2011 8:56 pm
Napisal/-a 2pac
realy
Here you have to be 16
and a theory exame 35 euro
i am luck in 2010 you have to do theory and practice 450 euro
25 and 45 km
Re: Im form the Netherlands and this are my mopeds
Objavljeno: Sr Jan 05, 2011 8:57 pm
Napisal/-a 2pac
Re: Im form the Netherlands and this are my mopeds
Objavljeno: Če Jan 06, 2011 12:15 am
Napisal/-a dj.umek
Look, you have standard 50cc machine, ctx machine is similar like 50cc on the out side, but it is diffrent inside.
ATX50 machine:smaller cilinder(50cc) ,carburator(bing 14/18) and smaler crankshaft, piston in original machine is fi38mm
CTX80 machine:bigger cilinder(80cc),carburator(bing21), bigger crankshaft,piston in original machine is fi46mm
I hope you see the diffrence now...
Re: Im form the Netherlands and this are my mopeds
Objavljeno: Če Jan 06, 2011 1:38 pm
Napisal/-a 2pac
Yes i know thnx for the info
Do you know how i can get to run my NtX 80Km/h with 50cc
I was thinking about
-Short the piston
-The intake of the cilinder bigger
-And the exhaust of the cilinder bigger
-15mm carburater power filter and 15mm intake
-other exhaust shock
Re: Im form the Netherlands and this are my mopeds
Objavljeno: Če Jan 06, 2011 2:07 pm
Napisal/-a Pich
Pipe homoet P4, carburetor 18-19, a little ported exshaust port, 1,5 mm lower head and bigger front sprocket. piston must be 46 mm long from edge where dome begins to end of the tail.
Re: Im form the Netherlands and this are my mopeds
Objavljeno: Če Jan 06, 2011 4:31 pm
Napisal/-a automatic_7
BT cilinder if you can find it
or kit for puch
Re: Im form the Netherlands and this are my mopeds
Objavljeno: Če Jan 06, 2011 4:33 pm
Napisal/-a koroman
Or you can buy a BT cylinder here on this forum and with homoet pipe and 18 carb is should run about 85km/h